Difference between revisions of "Manually Program Anytone-D878"

From PSRG Wiki
Jump to navigation Jump to search
Line 1: Line 1:
Warning: This is a draft-in-progress.


'''Adding WW7PSR (the PSRG repeater) as a channel in the Anytone AT-878UV via the keypad (programming manually)
'''How to add WW7PSR (the PSRG repeater) as a channel in the Anytone AT-878UV via the keypad (programming manually)
To program repeater 146.960, -0.6 MHz offset, 103.5 Hz CTCSS TX tone, wide band, high power level, into Channel #010'''.
To program repeater 146.960, -0.6 MHz offset, 103.5 Hz CTCSS TX tone, wide band, high power level, into a channel.


The [MENU/SELECT/CONFIRM] key is at the upper left corner of the keypad and features a solid green bar.
The [MENU/SELECT/CONFIRM] key is at the upper left corner of the keypad and features a solid green bar.
Line 7: Line 8:
The ▲ ▼ keys are on the round key between the [MENU] and [EXIT] keys. The ▲ key is marked with a single white line at the top. The ▼ key is marked with a single white line at the bottom.
The ▲ ▼ keys are on the round key between the [MENU] and [EXIT] keys. The ▲ key is marked with a single white line at the top. The ▼ key is marked with a single white line at the bottom.


* Turn on radio
* Turn on the radio.
* Press [MENU] and then use the ▲ ▼ keys to highlight '''Settings'''
* Press [MENU] and then use the ▲ ▼ keys to highlight '''Settings'''.
* Press [SELECT] to select '''Settings'''
* Press [SELECT] to select '''Settings'''.
* Use the ▼ key to highlight '''2 Chan Set''' and press [SELECT] to select '''2 Chan Set'''
* Use the ▼ key to highlight '''2 Chan Set''' and press [SELECT] to select '''2 Chan Set'''.
* Use the ▼ key to highlight '''New Chan''' and press [SELECT] to select '''New Chan'''
* Use the ▼ key to highlight '''New Chan''' and press [SELECT] to select '''New Chan'''.
** Note: When you select '''New Chan''' the channel number window will open, the next unassigned channel number is displayed by default in the lower right of the window. For our example, if the number displayed is anything other than 10 then press [DELETE] to delete it.  
** Note: When you select '''New Chan''' the channel number window will open, the next unassigned channel number is displayed by default in the lower right of the window. For our example, if the number displayed is anything other than 10 then press [DELETE] to delete it.  
* Use the keypad to enter "1" then "0" and then press [CONFIRM]
* Use the keypad to enter "1" then "0" and then press [CONFIRM]. After you enter the channel the Chan Name window will open, you can skip this for now by pressing [CONFIRM] or you may enter a name of your choice. You can also skip the Zone window by pressing [CONFIRM].
** Note: If you try to create a new channel using a channel number that has already been assigned you will get an error message. After you enter the channel the channel name window will open, you can skip this for now by pressing [CONFIRM] or you may enter a name of your choice. The #↑ key on the keypad is used to toggle between lower and upper letters and numbers.
** Note: If you try to create a new channel using a channel number that has already been assigned you will get an error message.  The #↑ key on the keypad is used to toggle between lower and upper letters and numbers.
* Use the ▼ key to highlight 3 Channel Type and press [SELECT] to select '''New Chan''' 1 A-Analog
* 4 TCTD 2CTC
* 8 Tx Power
* 9 Offset
* 11 Bandwidth




 
You can confirm that you've programmed the radio correctly by following the instructions
 
    
  To program repeater 146.960, minus offset, 103.5 Hz tone, low power level, into Channel #010
  * Turn on radio.
  * If in Memory Mode switch to VFO Mode (VFO/MR)
  * use VFO "A" only!
  * Select 5 KHz Step - (MENU + 1 + MENU) (Use the ▲ ▼ keys for 5K) (MENU + EXIT)
  * Enter 146.960 (The receive frequency)
  * Press [MENU] + 2 + [MENU] Use the ▲ ▼ keys to select Low Power
  * Press [MENU] + [EXIT] To accept and exit
  * Press [MENU] + 5 + [MENU] Use the ▲ ▼ keys to select Wide Bandwidth
  * Press [MENU] + [EXIT] To accept and exit
  * Press [MENU] + 1 + 3 + [MENU] Use the ▲ ▼ keys to select 103.5 Hz Tone
  * Press [MENU] + [EXIT] To accept and exit
  * Press [MENU] + 2 + 7 + [MENU] Enter 010 or Use the ▲ ▼ keys to select 010
   * Press [MENU] + [EXIT] This stores the Receive Frequency
  * Radio prompts that REC FREQ has been stored
  * Enter 146.360 (The transmit frequency)
  * Press [MENU] + 2 + 7 +
    [MENU] + [MENU] + [EXIT] Radio prompts that TX FREQ has been stored
  * Return to Memory Mode (VFO/MR)
 
== More Information ==
== More Information ==
This article is one of many [[:Category: How-to | how-to articles]] on our wiki.
This article is one of many [[:Category: How-to | how-to articles]] on our wiki.

Revision as of 18:59, 7 March 2020

Warning: This is a draft-in-progress.

How to add WW7PSR (the PSRG repeater) as a channel in the Anytone AT-878UV via the keypad (programming manually) To program repeater 146.960, -0.6 MHz offset, 103.5 Hz CTCSS TX tone, wide band, high power level, into a channel.

The [MENU/SELECT/CONFIRM] key is at the upper left corner of the keypad and features a solid green bar. The [EXIT/BACK/DELETE] key is at the upper right corner of the keypad and features a broken red bar. The ▲ ▼ keys are on the round key between the [MENU] and [EXIT] keys. The ▲ key is marked with a single white line at the top. The ▼ key is marked with a single white line at the bottom.

  • Turn on the radio.
  • Press [MENU] and then use the ▲ ▼ keys to highlight Settings.
  • Press [SELECT] to select Settings.
  • Use the ▼ key to highlight 2 Chan Set and press [SELECT] to select 2 Chan Set.
  • Use the ▼ key to highlight New Chan and press [SELECT] to select New Chan.
    • Note: When you select New Chan the channel number window will open, the next unassigned channel number is displayed by default in the lower right of the window. For our example, if the number displayed is anything other than 10 then press [DELETE] to delete it.
  • Use the keypad to enter "1" then "0" and then press [CONFIRM]. After you enter the channel the Chan Name window will open, you can skip this for now by pressing [CONFIRM] or you may enter a name of your choice. You can also skip the Zone window by pressing [CONFIRM].
    • Note: If you try to create a new channel using a channel number that has already been assigned you will get an error message. The #↑ key on the keypad is used to toggle between lower and upper letters and numbers.
  • Use the ▼ key to highlight 3 Channel Type and press [SELECT] to select New Chan 1 A-Analog
  • 4 TCTD 2CTC
  • 8 Tx Power
  • 9 Offset
  • 11 Bandwidth


You can confirm that you've programmed the radio correctly by following the instructions

More Information

This article is one of many how-to articles on our wiki.