Difference between revisions of "Manually Program Anytone-D878"
Jump to navigation
Jump to search
| Line 8: | Line 8: | ||
The ▲ ▼ keys are on the round key between the [MENU] and [EXIT] keys. The ▲ key is marked with a single white line at the top. The ▼ key is marked with a single white line at the bottom. | The ▲ ▼ keys are on the round key between the [MENU] and [EXIT] keys. The ▲ key is marked with a single white line at the top. The ▼ key is marked with a single white line at the bottom. | ||
* Turn on radio | |||
* Press [MENU] and then use the ▲ ▼ keys to highlight '''Settings''' | |||
* Press [SELECT] to select '''Settings''' | |||
* Use the ▼ key to highlight '''2 Chan Set''' and press [SELECT] to select '''2 Chan Set''' | |||
* Use the ▼ key to highlight '''New Chan''' and press [SELECT] to select '''New Chan''' | |||
** Note: When you select '''New Chan''' the channel number screen will open, the next unassigned channel number is displayed by defaultb in the lower right of the LCD screen. If the (If you try to create a new channel using a channel number that has already been assigned you will get an error message.) | |||
Revision as of 16:10, 7 March 2020
I'm planning adapt the text below to the Anytone AT-878UV. -KJ7LQP
Adding WW7PSR (the PSRG repeater) as a channel in the Anytone AT-878UV via the keypad (programming manually) To program repeater 146.960, -0.6 MHz offset, 103.5 Hz CTCSS TX tone, wide band, high power level, into Channel #010.
The [MENU/SELECT] key is at the upper left corner of the keypad and features a solid green bar. The [EXIT/BACK] key is at the upper right corner of the keypad and features a broken red bar. The ▲ ▼ keys are on the round key between the [MENU] and [EXIT] keys. The ▲ key is marked with a single white line at the top. The ▼ key is marked with a single white line at the bottom.
- Turn on radio
- Press [MENU] and then use the ▲ ▼ keys to highlight Settings
- Press [SELECT] to select Settings
- Use the ▼ key to highlight 2 Chan Set and press [SELECT] to select 2 Chan Set
- Use the ▼ key to highlight New Chan and press [SELECT] to select New Chan
- Note: When you select New Chan the channel number screen will open, the next unassigned channel number is displayed by defaultb in the lower right of the LCD screen. If the (If you try to create a new channel using a channel number that has already been assigned you will get an error message.)
To program repeater 146.960, minus offset, 103.5 Hz tone, low power level, into Channel #010
* Turn on radio.
* If in Memory Mode switch to VFO Mode (VFO/MR)
* use VFO "A" only!
* Select 5 KHz Step - (MENU + 1 + MENU) (Use the ▲ ▼ keys for 5K) (MENU + EXIT)
* Enter 146.960 (The receive frequency)
* Press [MENU] + 2 + [MENU] Use the ▲ ▼ keys to select Low Power
* Press [MENU] + [EXIT] To accept and exit
* Press [MENU] + 5 + [MENU] Use the ▲ ▼ keys to select Wide Bandwidth
* Press [MENU] + [EXIT] To accept and exit
* Press [MENU] + 1 + 3 + [MENU] Use the ▲ ▼ keys to select 103.5 Hz Tone
* Press [MENU] + [EXIT] To accept and exit
* Press [MENU] + 2 + 7 + [MENU] Enter 010 or Use the ▲ ▼ keys to select 010
* Press [MENU] + [EXIT] This stores the Receive Frequency
* Radio prompts that REC FREQ has been stored
* Enter 146.360 (The transmit frequency)
* Press [MENU] + 2 + 7 +
[MENU] + [MENU] + [EXIT] Radio prompts that TX FREQ has been stored
* Return to Memory Mode (VFO/MR)
More Information
This article is one of many how-to articles on our wiki.