Yaesu: Disable Wires - Revision history

N6NBN at 23:06, 30 June 2017

2017-06-30T23:06:11Z

← Older revision		Revision as of 16:06, 30 June 2017
Line 12:		Line 12:
	In most of the Yaesu manuals this is listed as Internet Connection Feature.		In most of the Yaesu manuals this is listed as Internet Connection Feature.

	'''Disabling Yaesu ~~Wires~~'''		'''Disabling Yaesu WIRES'''

	Wires is turned '''ON/OFF''' by pressing:		Wires is turned '''ON/OFF''' by pressing:

	FT-60 HT:		on the FT-60 HT:
	Momentarily press the 0 key.		Momentarily press the 0 key.

	FT-8800/8900 Mobile:		on the FT-8800/8900 Mobile:
	Momentarily press the LEFT volume knob.		Momentarily press the LEFT volume knob.

KI7LBE: add link to How-to category

2017-05-22T16:40:02Z

add link to How-to category

← Older revision		Revision as of 09:40, 22 May 2017
Line 92:		Line 92:
	select the same memory selected in step 3 above.		select the same memory selected in step 3 above.
	To re-enable the WIRES mode, select INT.COD in menu 17.		To re-enable the WIRES mode, select INT.COD in menu 17.

			== More Information ==
			This article is one of many [[:Category: How-to \| how-to articles]] on our wiki.

	[[Category: How-to]]		[[Category: How-to]]

KI7LBE: add category link

2017-05-22T15:40:48Z

add category link

← Older revision		Revision as of 08:40, 22 May 2017
Line 92:		Line 92:
	select the same memory selected in step 3 above.		select the same memory selected in step 3 above.
	To re-enable the WIRES mode, select INT.COD in menu 17.		To re-enable the WIRES mode, select INT.COD in menu 17.

			[[Category: How-to]]

KG7AUL at 16:28, 19 April 2017

2017-04-19T16:28:16Z

← Older revision		Revision as of 09:28, 19 April 2017
Line 8:		Line 8:
	This feature causes problems if turned on accidently. It sends a DTMF Tone when		This feature causes problems if turned on accidently. It sends a DTMF Tone when
	the PTT is keyed. Thus blanking out the 1st second or two of your transmission and		the PTT is keyed. Thus blanking out the 1st second or two of your transmission and
	can confuse the controller of your local Repeater~~. Our system replies “bad autopach~~		can confuse the controller of your local Repeater.
	~~number”~~.

	In most of the Yaesu manuals this is listed as Internet Connection Feature.		In most of the Yaesu manuals this is listed as Internet Connection Feature.

KG7AUL: Created page with "''Derived and copied from a [http://www.k0nr.com/wordpress/wp-content/uploads/2013/11/Turn-Off-Wires.pdf PDF hosted by K0NR]'' The Yaesu WIRES (Wide-coverage Internet Repeate..."

2017-03-06T17:04:44Z

Created page with "''Derived and copied from a [http://www.k0nr.com/wordpress/wp-content/uploads/2013/11/Turn-Off-Wires.pdf PDF hosted by K0NR]'' The Yaesu WIRES (Wide-coverage Internet Repeate..."

New page

''Derived and copied from a [http://www.k0nr.com/wordpress/wp-content/uploads/2013/11/Turn-Off-Wires.pdf PDF hosted by K0NR]''

The Yaesu WIRES (Wide-coverage Internet Repeater Enhancement System)
proprietary Internet Connection feature operates by transmitting a short (~ 0.1 second)
DTMF (Dual Tone Multi Frequency) tone burst each time the Push-to-Talk button is
pressed.

This feature causes problems if turned on accidently. It sends a DTMF Tone when
the PTT is keyed. Thus blanking out the 1st second or two of your transmission and
can confuse the controller of your local Repeater. Our system replies “bad autopach
number”.

In most of the Yaesu manuals this is listed as Internet Connection Feature.

'''Disabling Yaesu Wires'''

Wires is turned '''ON/OFF''' by pressing:

FT-60 HT:
Momentarily press the 0 key.

FT-8800/8900 Mobile:
Momentarily press the LEFT volume knob.

The WIRES function can be disabled so that it cannot accidentally be turned on using
the following steps:

'''FT-60''' (Manual page 49)

1. Press the F/M key then immediately press the 0 key to enter the menu mode.

2. Rotate the Dial knob to menu 23 – INT MR.

3. Press the F/M key then rotate the Dial knob to select a memory (d1 through d9)
that is empty, i.e. it contains •••••• (six dots) = no tone.

4. Press the F/M key to store the setting.

5. Rotate the Dial knob to menu 21 – I NET.

6. Press the F/M key then rotate the Dial knob to select INT.MEM.

7. Press the F/M key to store the setting.

8. Press the PTT button to exit the menu mode.

To re-enable the WIRES mode, select INT.COD in menu 21.

'''VX-170 & VX-177''' (Manual page 48)

1. Press the F/M key then immediately press the 0 key to enter the menu mode.

2. Rotate the Dial knob to menu 24 – INT MR.

3. Press the F/M key then rotate the Dial knob to select a memory (d1 through d9)
that is empty, i.e. it contains •••••• (six dots) = no tone.

4. Press the F/M key to store the setting.

5. Rotate the Dial knob to menu 22 – I NET.

6. Press the F/M key then rotate the Dial knob to select INT.MEM.

7. Press the F/M key to store the setting.

8. Press the PTT button to exit the menu mode.

To re-enable the WIRES mode, select INT.COD in menu 22.

'''FT-8800/8900''' (Manual page 50 or 48)

1. Press the SET key momentarily to enter the set mode.

2. Rotate the Main band Dial knob to select menu 15 – DTMF W.

DISABLING WIRES

1. Press the Main band Dial knob momentarily then rotate the Main band Dial
knob to select a memory (d1 through d16) that is empty, i.e. it contains ••••••
(six dots) = no tone.

2. Press the Main band Dial knob momentarily to store the setting.

3. Rotate the Main band Dial knob to select menu 17 – INET.

4. Press the Main band Dial knob momentarily then rotate the Main band Dial
knob to select INT.MEM.

5. Press the Main band Dial knob for ½ second to store the setting and exit the
menu mode.

6. Rotate the Main band Dial while pressing and holding the left VOL knob to
select the same memory selected in step 3 above.
To re-enable the WIRES mode, select INT.COD in menu 17.